Mechanically Interlocked Interphase with Energy Dissipation and Fast Li-Ion Transport for High-Capacity Lithium Metal Batteries.

Constructing an artificial solid electrolyte interphase (ASEI) on Li metal anodes (LMAs) is a potential strategy for addressing the dendrite issues. However, the mechanical fatigue of the ASEI caused by stress accumulation under the repeated deformation from the Li plating/stripping is not taken seriously. Herein, this work introduces a mechanically interlocked [an]daisy chain network (DC MIN) into the ASEI to stabilize the Li metal/ASEI interface by combining the functions of energy dissipation and fast Li-ion transport. The DC MIN featured by large-range molecular motions is cross-linked via efficient thiol-ene click chemistry; thus, the DC MIN has flexibility and excellent mechanical properties. As an ASEI, the crown ether units in DC MIN not only interact with the dialkylammonium of a flexible chain, forming the energy dissipation behavior but also coordinate with Li ion to support the fast Li-ion transport in DC MIN. Therefore, a stable 2800 h-symmetrical cycling (1 mA cm-2 ) and an excellent 5 C-rate (full cell with LiFePO4 ) performance are achieved by DC MIN-based ASEI. Furthermore, the 1-Ah pouch cell (LiNi0.88 Co0.09 Mn0.03 O2 cathode) with DC MIN-coated LMA exhibits improved capacity retention (88%) relative to the Control. The molecular design of DC MIN provides new insights into the optimization of an ASEI for high-energy LMAs.

Balancing the Ion/Electron Transport of Graphite Anodes by a La-Doped TiNb2O7 Functional Coating for Fast-Charging Li-Ion Batteries.

A functional coating layer (FCL) is widely applied in fast-charging lithium-ion batteries to improve the sluggish Li+ transport kinetics of traditional graphite anodes. However, blindly increasing the Li+ conductivity for FCL reduces the overall electron conductivity of the anodes. Herein, we decoupled the effect of La-doping on TiNb2O7 (TNO) in terms of the phase evolution, Li+/electron transport, and lithiation behavior, and then proposed a promising La0.1TNO FCL with balanced Li+/electron transport for a fast-charging graphite anode. By optimizing the doping concentration of La, more holes are introduced into the TNO as electron carriers without causing lattice distortion, thus maintaining the fast Li+ diffusion channel in TNO. As a result, the graphite with La0.1TNO FCL delivers an excellent capacity of 220.2 mAh g-1 (96.3% retention) after 450 cycles at 3 C, nearly twice that of the unmodified one.

Reversible Li Plating on Graphite Anodes through Electrolyte Engineering for Fast-Charging Batteries.

The difficulties to identify the rate-limiting step cause the lithium (Li) plating hard to be completely avoided on graphite anodes during fast charging. Therefore, Li plating regulation and morphology control are proposed to address this issue. Specifically, a Li plating-reversible graphite anode is achieved via a localized high-concentration electrolyte (LHCE) to successfully regulate the Li plating with high reversibility over high-rate cycling. The evolution of solid electrolyte interphase (SEI) before and after Li plating is deeply investigated to explore the interaction between the lithiation behavior and electrochemical interface polarization. Under the fact that Li plating contributes 40 % of total lithiation capacity, the stable LiF-rich SEI renders the anode a higher average Coulombic efficiency (99.9 %) throughout 240 cycles and a 99.95 % reversibility of Li plating. Consequently, a self-made 1.2-Ah LiNi0.5 Mn0.3 Co0.2 O2 | graphite pouch cell delivers a competitive retention of 84.4 % even at 7.2 A (6 C) after 150 cycles. This work creates an ingenious bridge between the graphite anode and Li plating, for realizing the high-performance fast-charging batteries.